Drawer organizer made to your drawer
Measure the drawer or the spot on your desk, pick the compartments and see the result at once.
Material and quantity
On the next page you pick the colour, the material and the print settings and ask for the price. Nothing is ordered or paid yet.
Tip: leave 1–2 mm of play on each side, drawers are rarely perfectly square. Prints without supports.
What the organizer does, how to design it to measure and what a print costs
The tool makes an organizer with compartments to the sizes you enter in millimetres: width and depth from 30 to 400 mm, height from 10 to 150 mm, up to 8 rows and 8 columns, that is 64 compartments, each at least 8 mm inside. All compartments are the same size and the organizer is one piece without a lid that prints without supports. The default wall is 1.6 mm and the bottom 1.2 mm, both adjustable from 0.8 to 4 mm, and the corners can be rounded. You can start from the preset "Drawer", "Desk supplies" or "Small parts". The preview redraws after every change and shows the outer size and the size of one compartment, so you see whether cutlery, batteries or screws will fit. It suits a drawer in the kitchen, the workshop or the bathroom, and a desk.
An example from the production calculator (18 October 2026, PLA+): a 200 × 120 × 40 mm organizer with 3 × 2 compartments weighs 115 g, prints in 2 h 27 min and costs 250 CZK (about 10 EUR) from us (calculation /c/l1gr0izblzwr); a small 100 × 80 × 30 mm one with 2 × 2 compartments weighs 41 g, prints in 57 minutes and costs 110 CZK, all without delivery. A 300 × 400 × 50 mm organizer is flagged by the calculator as bigger than a common bed: split such a drawer into two organizers side by side, or use the modular bins. If you own a printer, download the model free as a project for your machine (about 270 printers to choose from) or as an STL; a print from us ships by Packeta.
Before you order
How do I measure the drawer?
Measure the inside width and depth at the narrowest point (the corners at the bottom are often rounded) and take off 2 to 3 mm so the organiser goes in and out. Choose a height a few millimetres lower than the drawer, or it will not close.
How exact are the sizes?
A printer keeps sizes to a few tenths of a millimetre, and a large part may shrink a little as it cools. So allow 2 to 3 mm of play all round.
How much is it and how long does it print?
Mostly a matter of size and height. An organiser of 200 × 120 × 40 mm with 3 × 2 compartments prints in about two and a half hours and comes to 250 CZK (PLA+, without delivery). The calculation shows the exact time and price before you order anything.
Will a large organiser fit the printer?
The calculation shows straight away whether it fits the printer. If it is too big, split the drawer into two organisers or use the modular trays.
Which material?
PLA is enough for a drawer in an office or a workshop. For the bathroom or near the oven choose PETG, which copes better with heat and damp.
What if it does not fit?
We make the print to your sizes, so it cannot be returned without a reason. If it does not match the sizes of the order, that is a defect and you claim it.
Who it is for
Workshop
Bits, screws and wall plugs in the bench drawer: a grid of 4 × 3 compartments, about 40 mm high.
Kitchen
Cutlery, spices and small tools: an organiser exactly as wide as the drawer, in PETG.
Desk
Pens, chargers and cables: a shallow organiser of 20 to 30 mm so the drawer still closes well.
How it works
- Measure the drawer. Measure the inner width, depth and height of the drawer at its narrowest point. Leave 1 to 2 mm of play on each side, drawers are rarely exactly square.
- Enter the size and the compartments. Fill in the width, depth, height, rows and columns. You can start from the preset "Drawer", "Desk supplies" or "Small parts".
- Check the preview. The rotatable preview shows the shape, the outer size and the size of one compartment. It redraws with every change.
- Order the print or download. Choose the material, the colour and the number of pieces and continue to the exact price. Or choose "I have a printer, download the model".
What the tool can make
Common questions
How big an organizer can I design?
Width and depth from 30 to 400 mm, height from 10 to 150 mm. An organizer over 250 mm may not fit every printer; the calculator says so at once, and you then split the drawer into two organizers side by side.
How many compartments can it have, and can they differ in size?
Up to 8 rows and 8 columns, that is 64 compartments, each at least 8 mm inside. The grid is regular; for compartments of different sizes use the modular organizer of bins, where you lay out the arrangement yourself.
How thick are the walls and the bottom?
The default wall is 1.6 mm and the bottom 1.2 mm, enough for cutlery and desk supplies. Under "Wall thickness and more" you change both from 0.8 to 4 mm; for screws and heavy things choose 2 mm or more.
Can I add a lid or dividers of a different height?
Not in this tool: the organizer is open and all walls have the same height. The Custom box tool makes a box with a lid, the Modular organizer tool bins of different heights.
How do I print the organizer at home?
Flat, bottom down, without supports; the downloaded project carries the settings of the calculation (0.2 mm layers, 15 % infill). For the kitchen or the bathroom choose PETG, which takes heat and damp better; otherwise PLA is enough.
Do I have to have it printed by you?
No. Download the model free as a project ready for your printer, with about 270 printers to choose from, or as a plain STL file. A print from us is for those without a printer or with a large piece.
Where next
Looking for something else? See all Tools
