Phone stand

Pick a type, measure the phone with its case and adjust the sizes. The wedge and wide sizes suit a tablet too.

1Settings
2Preview and price
3Print or download

Type of holder

Plate with hooks Wave A-frame with a shelf Low wedge Wall pocket Car vent clip

Stand dimensions

Width mm 50–260 Phone thickness with case mm 7–20 Rest angle ° 35–80 Rest height mm 60–200 Depth mm 40–120 Vent slat thickness mm 1–4 Material thickness mm 3–8 Corner rounding mm 0–4

Cut-out for the charging cable
A slot in the shelf; the cable runs out freely under the stand. Window in the back rest
Saves about half the material, the stand stays stiff. With screw tabs
Otherwise it is fixed with double-sided tape.

Wall thickness and more

Material Colour Pieces

Rough price

—

An estimate from the model volume. The next step computes the precise price and print time.

Next you will see the precise price and print time. Order the print from us, or download the file for your own printer.

I have a printer, download the model

The design is saved, you pick your printer and download a ready project with print settings.

The plate with hooks prints upright on its base, the other stands lying down without supports, the wall pocket back plate down. Print the car clip in PETG.

A stand sized to your phone with its case

The tool offers six types of holder: a plate with hooks, a wave, an A-frame with a shelf, a low wedge, a wall pocket and a car vent clip. The stand is sized to the thickness of your phone with its case, entered in millimetres. For the desk types you set the width, rest angle and rest height. The wedge and the wide desk types suit a tablet too.

Every change redraws the preview and recalculates the rough price. We print the stand on our print farm in Czechia: it comes by Packeta to a pickup point or to your door. With your own printer you download the model free as a project or as an STL file. The angle is fixed by the design and cannot be changed later. The stand only holds the phone, it has no charger.

How it works

Pick the type of holder. For a desk choose the plate with hooks, the wave, the A-frame with a shelf or the low wedge. The pocket goes on a wall and the clip on a car vent.
Measure phone with case. Enter the thickness of the phone with its case, from 7 to 20 mm, and the width.
Adjust angle and extras. Set the rest angle and the rest height. Depending on the type you add a cut-out for the charging cable, a window in the back rest or fixing with screws.
Order the print or download. Check the preview and the rough price and continue to the precise price; a print from us is paid from credit topped up by card. Or download the model for your own printer.

What the tool can make

Desk A-frame with a shelf, 75 mm wide, rest angle 65°, cable cut-out.

Low wedge for watching video, 80 mm wide, 70 mm deep, angle 60°.

Wall pocket for a phone 80 mm wide, four screw holes.

Common questions

Will a phone in a case fit the stand?

Yes, if you enter the thickness of the phone with its case. The tool accepts a thickness from 7 to 20 mm and adds a little room itself.

Can I charge the phone in the stand?

Yes. The wave, the A-frame, the wedge, the wall pocket and the car clip can have a cut-out for the charging cable, and have it by default. The plate with hooks has no cut-out, the phone stands on two hooks there.

Does the stand suit a tablet too?

The width goes up to 260 mm and the rest height up to 200 mm, so the wedge and the wide desk types hold a tablet. The device with its case can be at most 20 mm thick, though.

How are the wall pocket and the car clip fixed?

The pocket sticks with double-sided tape, or with the screw option on you fix it with four screws. The clip pushes onto a vent slat whose thickness you enter, from 1 to 4 mm. Tape and screws are not part of the print.

Which material should the stand be printed in?

For a desk or a wall the everyday plastic (PLA) is enough. For the car clip we recommend the strong plastic (PETG), which handles heat better.

Looking for something else? See all Tools